Body — general description and precautions Golf/Touran cars have a load-bearing body. The base of the body, its side parts, roof and rear fenders are welded together. Therefore, serious body repairs, as well as the...
Mudguard of the engine — removal and installation Removing Attention! There is a risk of injury when jacking up the vehicle and placing it on jackstands. Familiarize yourself with the safety precautions regarding jacking up your...
Fairing grille — removal and installation Golf Cars Removing 1. Remove the glass cleaner brush holders. 2. Remove the sealing rubber 4 from the protrusion of the fairing 2 (see illustration). 40.2. Fairing grille -...
Front bumper — removal and installation Golf Cars Removing the bumper 1. Remove the grille. 2. Unscrew bolts 5 and 6 as well as lower bolts 4 (see illustration). 42.2. Front bumper. Golf Cars 1 - front bumper 2-4 -...
Rear bumper — removal and installation Golf Cars Removing 1. Remove the rear headlights. 2. Unscrew the bolts 5 that secure both rear fender liner (see illustration). 43.2. Rear bumper. Golf Cars 1 - rear bumper 2 -...
Radiator grill — removal and installation Golf Cars Removing 1. Open the hood. 2. Unscrew the two screws 4 (see illustration). 44.2. Radiator grille. Golf Cars 1 - radiator grille 2 - locking latches. six pieces 3 -...
Front fenders — removal and installation Golf Cars Removing 1. Remove the front bumper. 2. Remove the fender liner from the front wheel arches. 3. Unscrew three bolts and remove a lateral directing profile for a bumper....
Fender liner — removal and installation Front fender. Golf Cars Removing Attention! There is a risk of injury when the vehicle is jacked up or placed on jack stands. Familiarize yourself with the precautions for jacking...
Moldings — removal and installation Removing 1. Heat moldings 1-4 with a hair dryer and gradually and evenly detach them (see illustration). Installation Attention! Optimum conditions for gluing are provided at an...
Hood — removal and installation Removing 1 Open the hood. 2. Golf cars. Remove jets 6 from the hood (see illustration). 3. Golf cars. Disconnect the washing fluid supply hose, as well as the jet heater wire from...
Hood — fit Golf Cars 1. Unscrew the bolts securing the lock bracket 11 to the hood 5 (see illustration). 2. Disconnect the upper support of the gas-filled stop 4 from the hood (see...
Bonnet lock — removal, installation and fitting Attention! This chapter describes how to remove and install the bonnet latch and the lock shackle on Golf vehicles. Removal and installation of the hood lock are carried out...
Hood lock cable — removal and installation Removing 1. Pull up the hood opening handle 1, located in the footwell of the driver's side (see arrow in illustration). 2. Pry with a screwdriver, pull out clip 2 a little and...
Gas-filled emphasis — removal and installation Removing 1. Open and have an assistant support the tailgate or hood. Attention! When removing the stop, the rear door must be supported by an assistant. Otherwise, it will slam...
Mirror glass — removal and installation Removing 1. Tape the edge of 1 mirror body with adhesive tape to protect it from damage (see illustration). 2. Press down on the mirror glass 2 and press it into housing 1 (see...
Rear view mirror housing — removal and installation Golf Cars Removing 1. Remove the mirror glass. 2. Tilt the mirror housing forward. 3. Insert a screwdriver under the latch 2 and press the latch (see illustration). 4. Move the...
Side rear-view mirror — removal and installation Golf Cars Removing 1. Remove an upholstery from a forward door. 2. Remove the screw. Which is attached to the triangular lining near the window opening. 3. Pry off the triangular...