Internal elements of car body Volkswagen Passat B3

Removal and installation of a cable drive of a cowl
1 - drive lever 2 - screw 3 - sealing insert 4 - clamp 5 - guide 6 - cable sheath clamp 7 - fastening bolt Self-locking, therefore replace. In case of repeated use, clean the...

Removal and installation of the luggage compartment lid lock
1 - lock cylinder body The lock cylinder housing is removed in the same way as the PASSAT Variant models. Attention: Since 10/93, the execution has been changed, but the removal...

Removal and installation of the lock / case of the cylinder of the lock of a back door
Variant Model 1 - lock cylinder body Attention: Since 10/93, the execution has been changed, but the removal is carried out as before. 2 - nut, 6 Nm With a non-falling puck. 3 -...

Removal and installation of the lock cylinder
Car models since 10/33 1 - lock cylinder body 2 - push button spring 3 - push button 4 - sealing ring 5 - lock cylinder Attention: Pull out the lock cylinder only with the key...

Central locking system
1 - actuating element of the lock of the fuel tank cap 2 - foam tube 3 - tee-distributor 4 — an executive element of the lock of a back door 5 - adapter 6 - executive elements of...

Removal and installation of an executive element of the lock of a forward door
Note: Pay attention to the special items related to the driver's side door. Other executive elements are removed and installed accordingly. Removing Remove door trim. Remove the...

Removal and installation of the gas-filled shock-absorber of a back door
Removing Open the back door and prop it up. Swing out retaining clip -1- to one side and pull out. Using a screwdriver, lift locking clip -2- and remove gas spring from ball stud....

Removal and installation / adjustment of the door
1 - door 2 - door hinge The hinge is screwed to the door, inserted into the A-pillar and locked with a countersunk screw. 3 - bolt, 55 Nm 4 - door latch cover Self-adhesive, glued...

Removal and installation of window glass of a forward door
Removing Remove inner door trim. Remove the window glass inner seal from the flange. Lower the window glass down and unfasten it from the power window. Tilt the glass forward and...

Removal and installation of an external guide of window glass
Removing Remove inner and outer triangular trim. If necessary, remove the outside mirror. Remove the outer seal of the window shaft from the flange. Remove the inner window glass...

Removal and installation of a window regulator of a forward door
Removing Remove inner door trim. Slide the glass upwards and secure, for example with adhesive tape. Remove bushing -12- from power window shaft. Loosen the power window mount....

Removal and installation of the door lock
1 - door handle For vehicles with extra comfort control (central locking system, power windows) the cover must first be removed and the plug connector disconnected. The free play...

Removal and installation of the door handle
Removing Remove the screw (dashed arrow). Starting with chassis no. NE 190000, the screw mounted on the right has a left-hand thread. Slide the handle in the direction of the...

Removal and installation of internal door seal
Removing Remove inner door trim. Remove the inner door seal from the flange. Installation Push the inner door seal onto the edge so that the joint -2- of the seal is at a distance...

Removal and installation / adjustment of the rear door
1 - door 2 - door hinge The hinge is screwed to the door, inserted into the B-pillar and locked with a countersunk screw. 3 - bolt, 55 Nm 4 - door latch cover Self-adhesive, glued...

Removal and installation of a window regulator of a back door
Removing Remove inner door trim. Detach the window glass from the power window. Slide the glass upwards and secure, for example with adhesive tape. Remove bushing -12- from power...

Removal and installation of window glass of a back door
Removing Remove inner door trim. Lower the window glass down. Remove the inner and outer triangular covers. Unscrew the window glass guide -14 - and pull it upwards out of the...

Replacing the outer window glass guide
Removing Remove inner and outer triangular trim. If necessary, remove the outside mirror. Remove the outer seal of the window shaft from the flange. Remove the inner window glass...

Trunk lid adjustment
Passat with a pronounced angle between the rear window and the trunk Adjustment The trunk lid is guided by sliding plates -2- and an installation buffer -1-. Fit stop buffer -4-...

Rear door adjustment
Removing 1 - threaded bushing (left hand thread) 2 - remote strut 3 - spacer pin with a slot for dismantling 4 - locking tabs for basic adjustment 5 - recess for the fixing...

Removal and installation of facing of a door
Car models up to 9/93 1 - lock button 2 - socket 3 - decorative overlay 4 - power window handle Position with fully closed window glass: 45°±12°. 5 - inner door handle 6 -...

Rear door lining
Note: since 10/93, the door lining has been changed, the front door linings are analogous. One-piece cladding 1 - lock button Unscrew from the bar. 2 - socket 3 - decorative...

Removal and installation of the average console
1 - fixing protrusion 2 - hand brake lever handle 3 - facing 1 - casing For gear lever on vehicles with manual transmission. 2 - casing For gear lever on vehicles with automatic...

Visual inspection of seat belts
Attention: Noises that occur when the seat belt is retracted are functionally caused. In case of disturbing noises, only the seat belt is replaced. Under no circumstances should...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Passat B6 Passat B5 Passat B4

Passat B3 Passat B2