Rear suspension device

Front wheel drive vehicles

Rear suspension of front wheel drive vehicles

• 1 - shock absorber,
• 2 - spring,
• 3 - beam,
• 4 - upper spring support,
• 5 - shock absorber support,
• 6 - buffer,
• 7 - brake disc,
• 8 - bearing,
• 9 - stabilizer,
• 10 - hand brake cable,
• 11 - rubber-metal support

Elements of the rear suspension of front-wheel drive vehicles

• 1 - upper spring support,
• 2 - wheel rotation sensor holder,
• 3 - wheel rotation sensor,
• 4 - spring,
• 5 - hub bearing,
• 6 - rubber-metal support with a bracket,
• 7 - nut,
• 8 - bolt M12x1.5x90, 110 Nm + tighten by an angle of 90°,
• 9 - bolt M12x1.5x60, 110 Nm + tighten by 90°,
• 10 - rear beam,
• 11 - bolt M14x1.5x190, 120 Nm + tighten by an angle of 90°,
• 12 - stabilizer clamp,
• 13 - threaded hole,
• A - the direction of movement of the car,
• B - right side of the car

Warning: Spring 4 must not show damage to the paintwork.

Warning: Before installation, clean the bearing surfaces of the bracket with rubber-metal support 6. After installation, check and, if necessary, adjust the track of the rear wheels.

Warning: When installing nut 7, it is recommended to use a new nut.

Warning: When installing bolts 8, 9, 11, it is recommended to use a new bolt.

Warning: Before installation, clean the bearing surfaces of the rear beam 10.

Front wheel drive shock absorber

• 1 - gas-filled shock absorber,
• 2 - nut,
• 3 - bolt M10x90, 50 Nm + tighten by an angle of 90°,
• 4 - protective cover,
• 5 - protective cover,
• 4 - protective cover,
• 5 - protective cover,
• 6 - buffer,
• 7 - bolt, 45 Nm,
• 8 - upper shock absorber mount,
• 9 - self-locking nut, 25 Nm,
• 10 - threaded holes in the car body

Warning: Shock absorber 1 is replaced as an assembly.

Warning: When installing nuts 2, 9, it is recommended to use new nuts.

Warning: When unscrewing nut 9 with a second wrench, keep the shock absorber rod from turning.

Warning: When installing bolt 3, it is recommended to use a new bolt.

The base of the rear suspension is a beam with levers welded to it. A stabilizer is installed in front of the rear beam, which reduces the roll of the car when cornering. The rear beam is attached to the body through rubber-metal bushings. The rear beam is damped by separate springs and shock absorbers. As a result of the separate arrangement of the rear suspension springs, the volume of the luggage compartment has increased.

4x4 vehicles

Rear suspension beam for all-wheel drive vehicles

• 1 - rear main gear,
• 2 - bracket,
• 3 - beam,
• 4 - rubber-metal support

Rear suspension arms for all-wheel drive vehicles

• 1 - beam,
• 2 - upper lever,
• 3 - hub fastener,
• 4 - bearing,
• 5 - hub,
• 6 - shield,
• 7 - brake disc,
• 8 - lower arm

The rear suspension consists of a beam with two wishbones and suspension struts on each side of the car. The beam is attached to the car body with four rubber-metal supports.

Warning: Welding and straightening work are not allowed on the bearing elements of the rear suspension. When installing, use new self-locking nuts and replace bolts that show signs of corrosion.