Removal and installation of a headlight Pic. 7.43. headlight components: 1 - left headlight corrector servo or right headlight corrector servo; 2 - retaining ring; 3 - left headlight corrector servo or right headlight...
Headlight adjustment Note: The illustrations show the left headlight. Note: Correction of the position of the left headlight is similar to the work on the correction of the right headlight. Note: If,...
Replacing the Low Beam Bulb Note: The left dipped beam bulb and the right dipped beam bulb can be checked using the final control diagnosis of the onboard power supply control unit. Removing Switch off the...
High Beam Bulb Replacement Note: The left main beam bulb and the right main beam bulb can be checked using the final control diagnosis of the onboard power supply control unit. Removing Switch off the...
Parking light bulb replacement Note: The parking light bulb left and the parking light bulb right can be checked using the final control diagnosis of the onboard power supply control unit. Removing Switch off...
Headlight adjustment check Conditions for checking and adjusting Tire pressure should be correct. Diffusing glasses must be clean and undamaged. Reflectors and lamps are OK. The car must be properly loaded....
Headlight adjustment with gas discharge lamps Carrying out basic setup Connect the diagnostic tester. Pic. 7.70. Location of the diagnostic connector Turn on the ignition (pic. 7.70). Click «Guided Functions». Perform vehicle...
Headlight adjustment with halogen lamps Note: Check if both headlights work the same when manual headlight beam throw adjustment is turned on. Right headlight adjustment The left headlight adjustment screws are...
Main headlights with gas discharge lamps Note: Before working on headlights with discharge lamps, turn them off and turn the key to position 0 (pre-stop). Note: Automatic headlight range control and adaptive headlamp...
Replacing the discharge lamp Note: The left and right discharge lamps can be checked using the final control diagnosis of the onboard power supply control unit. Note: The illustrations show replacing the HID...
Removing and installing license plate lights (sedan) Removing Switch off the ignition and all electrical consumers and turn the key to position 0 (pre-stop). Pic. 7.89. Mounting bolts for license plate light Unscrew the mounting...
Removal and installation of the contact switch of a cowl Removing Switch off the ignition and all electrical consumers and turn the key to position 0 (pre-stop). Remove the hood latch. Unlock and disconnect plug connection 2. Pic. 7.93....
Removal and installation of the light switch Removing Switch off the ignition and all electrical consumers and turn the key to position 0 (pre-stop). Turn the light switch knob to the position «0». Press the rotary handle...
Removal and installation of illumination of a glove box Note: When removing and installing items that are in sight (switches, covers, trim panels, etc.), seal the places where the tool, wedge, screwdriver, etc. are used with ordinary...
Removal and installation of switches of the central console Removal and installation of the following items is carried out in the same way, so the description is given for only one item. Note: When removing and installing items that are in...
Removal and installation of the main fuse box The main fuse box is located in the trunk, behind the left wheel well above the battery. Removing Remove the pyrotechnic disconnector. Pic. 7.109. Fixing nuts of the main fuse box...
General instructions for car electrical repairs Attention: When disconnecting and connecting the battery, be sure to follow the sequence of actions described in the repair manual. Attention: Some tools have a safety loop, which...
CAN bus wiring repair The CAN bus wire is 0.35 mm two-wire wire 1 and 2 2 or 0.5 mm 2 . The color coding of the CAN bus wires can be found in the following table CAN-High bus wire, drive orange/black;...
Broken wire with repair in two places Release the wire to be repaired in two places (approx. 20 cm on both sides of the respective repair site). If necessary, remove the wiring harness wrap with a jackknife. Lay the...
Repair of contacts in connector housings First, if necessary, open or unlock the secondary fastening of the connector housing. Pic. 7.135. Unblock a contact Unblock a contact (primary fastening) a suitable pick (pic....
Mechanical locking of the connector housing The secondary fixing is the connector housing retainer that secures all wires to the connector housing. If the connector housing has a secondary fastening, then before unlocking...
Round contacts Note: Before unlocking the contacts, you must unlock or remove the housing locks, if any (secondary mounts) special tool. Pic. 7.140. Entering a master key into a slot in the...
Flat contacts with asymmetrical locking tabs Insert a pick suitable for the connector housing into the slot in the connector housing. Grasp the wire to the pin and lightly push it into the connector Note: By pushing the tip...