Vehicle equipment and instruments after 2000 Volkswagen Polo 3

Removal and installation of the instrument panel
The instrument panel is equipped with a self-diagnosis system. Before removing it, it is necessary to read the fault codes using the VAG 1551 fault code reader or the VAG 1552...

Rear view of instrument panel
The rear view of the instrument panel is shown in fig. 12.32. Pic. 12.32. Rear view of the instrument panel: 1 - 32-pin wiring connector, blue; 2 - Sound signaling device; 3 -...

Instrument cluster self-diagnosis preparation
Connecting the VAG 1551 fault code reader and selecting functions (determining the version of the instrument panel control unit). 1. Remove insert 1 of the ashtray and connect the...

Instrument panel fault codes
Fault codes for the instrument panel are shown in table 12.1. Fault code Faulty item 01086 Speed sensor 00779 Outdoor temperature sensor 01044 Control unit incorrectly coded 01312...

Removing and installing the immobilizer control unit
Elements of the immobilizer are shown in fig. 12.34. Pic. 12.34. Immobilizer elements: 1 - Immobilizer control unit; 2 - Transmitter integrated into the key; 3 - Fuel cut-off...

Removal and installation of the light switch
Removing 1. Set the light switch knob to position «0». 2. Push the knob in the direction of arrow 1 and turn it to the right in the direction of arrow 2 (pic. 12.38). While...

Removal and installation of switches on the instrument panel
Removing the switches on the instrument panel is done with a screwdriver (pic. 12.40). After removing the switch, disconnect the wiring connector from it.

Heating system and air conditioning
Volume for filling refrigerant R134a. Compressor - SD7-V16. Producer - Sanden. Volume - 850+30 grams. Elements of the heating system are shown in fig. 12.41. Pic. 12.41. Elements...

Removal and installation of the dust and pollen filter
Removing 1. Remove the rubber seal 1, starting from the middle of the car (pic. 12.42). Unhook the latches (arrows) ventilation chamber cover and remove cover 2. 2. Move the cover...

Removal and installation of deflectors
Removing the central deflectors 1. Remove radio 1 (pic. 12.44). Remove ashtray 2. 2. Remove the screws (arrows A) and install the mounting tabs up (arrows B) (pic. 12.45). 3. Lift...

Removal and installation of regulators of a heater
Removing 1. Remove the cover in space 1 (pic. 12.51). 2. Remove the decorative panel from the controls (arrows) (pic. 12.52). 3. Loosen the screws (arrows) (pic. 12.53). 4. Remove...

Disassembly and assembly of the heater
The heater in a disassembled state is shown in fig. 12.58. Pic. 12.58. Heater disassembled: 1 - Heater radiator; 2, 5, 8 - Screws; 3 - Air distributor; 4 - Fresh air supply / air...

Location of elements of the air conditioning system
The location of the elements of the air conditioning system is shown in fig. 12.61. Pic. 12.61. Location of elements of the air conditioning system: 1 - Vacuum and discharge valve...

A/C compressor bracket (ARE engine)
A/C compressor bracket (ARE engine) shown in fig. 12.65. Pic. 12.65. A/C compressor bracket (ARE engine): 1 - Bracket for the generator, air conditioning compressor and power...

AC compressor electromagnetic clutch (Sanden)
AC compressor electromagnetic clutch (Sanden) shown in fig. 12.66. Pic. 12.66. AC compressor electromagnetic clutch (Sanden): 1 - Nut; 2 - Connecting plate; 3 - Bushing; 4, 6 -...

Evaporator and condenser device
The evaporator is shown in fig. 12.67. Pic. 12.67. Evaporator: 1 - Sealant between the heater radiator and the partition of the engine compartment; 2 - Heater radiator; 3 - The...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Polo 4 Polo 3