Fuel supply system List of parts and assemblies of the fuel tank with technological notes on repair to drawing VC3.063: 1. Ground connection: - check the security of fastening. 2. Neck fixing...
Fuel filter parts and assemblies List of parts and assemblies of the fuel filter with technological notes on repair to drawing VC3.065: 1. Pressure line from the fuel tank: - color: white or with a white label....
Removal and installation of the fuel supply module 1. Unscrew the union nut using a special wrench (1). 2. Remove the fuel supply module with sealing washer from the hole in the fuel tank. Attention! When replacing a fuel delivery...
Removal and installation of the fuel level sensor Removing 1. Remove the fuel delivery module. 2. Unlock and disconnect wire terminals (3) And (4). 3. Pry off the hinges (1) And (2) screwdriver and remove the fuel level sensor by...
Removal and installation of the dual pump Removing 1. Disconnect pressure (white marking) (1) and reverse (blue marking) (2) fuel filter hoses. 2. Extract fuel with a manual vacuum pump (3). 3. Remove the air filter...
Fuel and vacuum pump Fuel and vacuum pump 1.9 / 2.0 l BDJ, BJB, BST, BLS, BSU. Specification for drawing VC 3.072 Pos. Detail number Name Note PC. 1 038 145 209 E Fuel and vacuum pump F 2К-5-093583 1...
Quick Hose Couplings For connections of hoses of system of pressurization spring collars and quick disconnect couplings are used. Observe the following rules when working with quick couplings. When...
1.9L BJB turbocharged air supply system The list of components and parts of the intake tract of the diesel engine 1.9 l BJB with technological notes on repair to drawing VC3.074: 1. Screw: 10 Nm. 2. Union nut: 22 Nm. 3....
1.9L BJB Intercooler Components and Parts 1.9L BJB Diesel Charge Air Intercooler Specification for Drawing VC3.076 Pos. Detail number Name Note PC. 1 1K0 145 803 A Charge air cooler 1 1A 1J0 145 769 N Duct clamp 2 1B...
1.9L BLS and BSU turbocharged air supply system List of components and parts of the intake tract of diesel engines 1.9 l BLS and BSU with technological notes on repair to drawing VC3.077: 1. Heat shield fixing screw: 10 Nm. 2....
Removal and installation of a turbocharger If mechanical defects are found on the turbocharger, such as a defective impeller, it is not sufficient to simply replace the turbocharger. In order to avoid the appearance of...
Non-turbo air supply system Specification of components and parts of the intake tract of diesel engines 2.0 l VO J and BST to drawing VC3.086 Pos. Detail number Name Note PC. 1 1F0 129607 Air filter 1 (1)...
Fuel injection system — description In the described engines, pump-injectors are used for fuel injection. These devices differ from a conventional high-pressure fuel pump in that each pump-injector supplies fuel to...
Specification of unit injectors for diesel engines Specification for pump injectors for diesel engines 1.9 with BJB, BLS, BSU, as well as diesel engines 2.0 l VKS, BDJ, BST to drawing VC3.087 Pos. Detail number Name Note PC. 1...
Vacuum hose connection diagram Vehicles with particulate filter List of assemblies and parts for drawing VC3.088: 1. Turbocharger. 2. Connecting tube air filter/turbocharger. 3. Check valve. 4. To the brake...
Removal and installation of an accelerator pedal List of assemblies and parts of the accelerator pedal module for drawing VC3.090: 1. Connector black, 6-pin. 2. Accelerator pedal position sensor (G79): - not regulated; - the...
Particulate Filter Related Parts List of parts and assemblies with notes on installation work to Figure VC3.096: 1. Exhaust pressure sensor (G450). 2. Control line: - connection to the particulate filter outlet:...
Parts and components of the exhaust gas recirculation system List of parts and assemblies with notes on installation work to Figure VC3.101: 1. Intake manifold with EGR valve and air damper. - tighten the fastening bolts to 22 Nm. 2. From...
Vacuum hose connection diagram (BJB, BSU and BLS) Location of branch pipes on the solenoid valve block of BJB, BSU engines: 1. Vacuum line connection (on the non-return valve for the brake booster) 2. EGR valve 3. Air damper 4....
Silencer with mounts — design description List of parts and assemblies with notes on installation work to Figure VC3.105: 1. Gasket: - when assembling, replace with a new one. 2. Support. 3. Exhaust manifold with...
Details of the exhaust gas recirculation system Attention! Exhaust gas recirculation is controlled by the diesel direct injection system control unit (3248) with EGR valve (N18) and a vacuum exhaust gas recirculation valve...