Cooling system 1.4L petrol engine Volkswagen Caddy 3

Elements of the lubrication system
The lubrication system is equipped with a rotary oil pump driven directly by the crankshaft. A heat exchanger is included in the lubrication system. Specification of the elements...

Removal and installation of parts of the lubrication system
Attention! If, during the repair, metal chips were found in the engine in large quantities, this may be due to a malfunction of the connecting rod bearing. To avoid subsequent...

Removal and installation of an oil filler neck
Removing 1. Remove check valve (1) from the oil filler neck. 2. Carefully lift the oil filler neck and turn it in the direction (arrows). 3. Remove the oil filler neck from the...

Removal and installation of the pallet of an oil crankcase
Removing 1a. Remove soundproof cover. For engines with the letter designation BCA 2a. Remove the exhaust pipe from the exhaust system. For engine codes BUD 26. To remove a...

Removing and installing the oil pump
Removing 1 Remove the main timing belt. 2 Fix the crankshaft sprocket (1) old screw (2) to the crankshaft. 3. Set the crankshaft to the TDC position of cylinder No. 1. 4. The...

Connection diagram of the cooling system
VC2.080. Connection diagram of the cooling system: 1. Expansion tank 2. intake manifold 3. Tube of the cooling system, upper - fixed on the distribution housing 4. Heater heat...

Details and units of the hydraulic part of the cooling system
Specification of parts and assemblies of the hydraulic part of the cooling system to drawing VC2.081 Pos. Detail number Name Note PC. 1 b036121005S Coolant pump with bonded gasket...

Parts and assemblies of the thermostat, radiator and expansion tank
Specification of parts and assemblies of the thermostat, radiator and expansion tank to drawing VC2.082 Pos. Detail number Name Note PC. 1 032121111VM thermostat housing 1 2...

Parts and assemblies of the cooling fan unit
Specification of parts and assemblies of the cooling fan unit to drawing VC2.083 Pos. Detail number Name Note PC. Shroud for two fans Gasoline engines 1.4-2.0 l BCA, BGU, 8SE,...

Precautions when working with the cooling system
Attention! Hot steam may come out when the expansion tank is opened. To avoid eye injuries and burns, you need to work in goggles and special clothing. The lid should be covered...

Elements of the cooling system installed on the body
Attention! Depending on the configuration, vehicles are also equipped with one cooling fan. The removal and installation process is the same as described below for the dual fan....

Elements of the cooling system associated with the thermostat
Elements of the system associated with the thermostat: 1. Thermostat connection. 2. Self-tapping screw for fastening the thermostat pipe: 7 Nm. 3. O-ring: - when assembling,...

Elements of the system associated with the coolant pump
List of parts and assemblies of the cooling system (coolant pump) with technological recommendations for repair to drawing VC2.086: 1. Toothed belt of the main timing drive: -...

Removal and installation of the fan, radiator (V7) and radiator fan 2 (V177)
Removing 1. Remove the acoustic cover. 2. Set the hood latch console to the service position. 3. Disconnect connector (1) and unscrew the screws securing the fan bracket (arrows)....

Removal and installation of a radiator
Removing 1. Move the bonnet lock console to the service position. 2. Drain the coolant. 3. Remove the guide screen with air intake. 4. Disconnect the cooling system hoses from the...

Removal and installation of the pump of a cooling liquid
Removing 1. Drain the coolant. 2. Remove poly V-belt. 3. Then remove the toothed belt of the main drive. 4. Remove guide roller (6), for which to unscrew the fastening screw (5)....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Caddy 3 Beetle