Replacement of interior lighting lamps
Bonnet lamp replacement
Replacing incandescent outdoor lighting
1. Turn off the corresponding lamp switch.
Farah
2. Open the bonnet.
3. If necessary, replace the left headlight bulb: unscrew the battery cover and remove.
4. Disconnect the plug at the back of the headlight.
5. Remove the rubber cap from the back of the headlight.
6. Compress spring clip (1) lamp holder and fold down.
7. Remove the defective lamp.
8. Do not touch the bulb of the new lamp with your hands. Install the lamp so that the spouts fit into the corresponding cutouts in the housing. The middle tongue on the lamp base should be at the top.
9. Raise the spring clip, compress and lock.
10. Put the rubber cap on the back of the headlight, inserting the tabs into the cutouts. Put the plug on the frame.
11. If removed, install and secure the battery guard.
12. Check the headlight adjustment at the service station.
Parking light front
13. The parking light bulb is located in the headlight reflector. Turn the lamp base to the left and pull it back out of the reflector. The connecting wire on the plinth can not be removed.
14. Insert the lamp into the frame, turn to the left and remove.
15. Insert new bulb, turn to the right and lock.
16. Insert the bulb holder into the reflector and turn to the right as far as it will go.
Front turn signal
17. Open the bonnet.
18. Insert a screwdriver from above between the headlight and turn signal housing. The locking tab will bend to the side.
19. Lower the screwdriver forward in the direction of the arrow, thereby removing the turn signal housing forward.
20. Remove the forward direction indicator assembly.
21. Turn the lamp frame to the left and remove it from the housing.
22. Slightly sink the lamp into the frame and turn it 90° (1/4 turn) to the left and pull out.
23. Install the new bulb, push lightly and turn to the right.
24. Insert the frame into the turn signal housing (turn all the way to the right).
25. Insert indicator light into guides (up and down), push until the locking tab snaps into place.
Anti-fog headlight
26. Unscrew the protective cap on the back of the fog lamp to the left (under the bumper).
27. Remove the spring clip of the lamp holder, remove the burned-out lamp.
28. Install a new lamp so that the spouts fit into the corresponding cutouts in the housing.
29. Put on and lock the spring clip.
30. Screw on the protective cap.
31. Check the adjustment of the fog lights at the service station.
Rear lights
32. Open the trunk lid.
33. Grab both locking tongues of the lamp unit from the side of the trunk, squeeze them together and pull the unit out.
34. Push in defective bulb, turn 45°to the left and remove.
35. Push the new bulb into the frame, turn to the right and lock.
36. Insert the lamp unit into the housing, the tabs should click into place.
Rear fog lamp
37. Press the locking tab of the fog light (arrow) and take out the diffuser.
38. Pull out the lamp housing.
39. Turn the frame of the defective lamp to the left and remove.
40. Unscrew the lamp from the frame to the left and replace.
41. Install the lamp diffuser on the left side and push in until the locking tab clicks into place.
License plate lighting
42. License plate lights are fixed with 2 screws each (indicated by arrows). Unscrew the diffuser with a Phillips screwdriver.
43. Remove the license plate light.
44. Remove the frame from the lamp.
45. Slightly sink the lamp into the frame, turn to the left by 90° (1/4 turn) and take out.
46. Install a new bulb, push it in slightly and turn to the right.
47. Install a flashlight.
48. Install diffuser and screw lightly. Turn off the corresponding lamp switch.
Replacing the lamp on the ceiling of the machine
49. Remove the night light from the side opposite the switch.
50. Rotate the frame of the lamp on the reverse side by 90° (1/4 turn) to the left and remove the lamp. Install a new lamp.
51. Remove the diffuser and replace the soffit lamp. If the lamp does not sit firmly, bend the contacts.
52. Install the lamp in the ceiling cutout.
Footrest and boot lamps
53. Insert a narrow screwdriver into the side cutout of the diffuser (on the side opposite the switch) and take out the lamp.
54. Replace soffit lamp. If the lamp sits loose, bend the contacts slightly.
55. Insert the lamp first with the side towards the switch, then insert the other side.
56. Squeeze the diffuser and remove.
57. Push the lamp slightly into the frame, turn it 90°to the left (1/4 turn) and take out.
58. Install a new bulb, push it in slightly and turn to the right.
59. Install diffuser and lock.
Visitor comments